Grout Material

Grouts used in civil construction and rehabilitation projects can be generally categorized into either a cement or chemical grout. Within each grout family, there are primary grout subtypes: within the cement grout family, ordinary Portland cement and ultrafine cements define these subtypes. The chemical grout family includes sodium silicate, acrylic gels and polyurethane expansive foams. Although each parent grout type has primary grout spawns, this is where the commonalities end and the individual grout types split into their own unique characteristics.

Cement grouts are considered to be suspended solids grouts, because they have particulates that comprise their composition which is derived from grinding Portland cement clinker. The level of grinding effort applied to the clinker determines the average particulate size. Portland cement grout generally has particulate sizes on average of 15 microns. Microfine cements range from 6 to 10 microns while ultrafine cements can have average particulate sizes of 3 to 5 microns. US Grout in Malad, Idaho, can provide custom blended cementitious grouts meeting project specific requirements.

A grout’s ability to penetrate a rock fissure largely depends on particulate size whereas its ability to permeate a soil is also dependent upon surface tension within the grout. A cement’s rheology, which is the grout’s ability to flow, is accomplished through the control of the water/cement ratio and almost always a superplasticizer is added to reduce viscosity. While additives can be added to slow the cure time, once mixed with water, cement grouts will begin to cure and create high compressive strength. Once injected, cements are considered long-term solutions for either water control or structural improvement having lifespans ranging between 100 to 200 years. Ordinary Portland cement costs (mixed) will typically range between 1 and 2 dollars a mixed gallon while microfine/ ultrafine cements costs (mixed) will typically range between 3 and 4 dollars per mixed gallon. These costs can further reduce when higher water/cement ratios are employed.

The primary types of chemical grouts (silicates, acrylics and polyurethanes) are each unique in composition. Although it’s truly a suspended solids grout, because the particulates are so small sodium silicates have a high degree of penetrability into soils and rock, very similar to the true solution grouts, which have no suspended solids.

Sodium silicate is a two-component grout that typically has very low viscosity but will often expunge water after gelling by a process called syneresis. Sodium silicates can be sensitive, bordering on unstable, when injected into any groundwater condition. With relatively short gel times, a few minutes to a few hours, sodium silicates are commonly used as temporary solution for water control or structural support with an estimated life span of a few years. Longer life spans can be experienced with silicates depending on the chemistry of the soils. Sodium silicates typically range between 2 and 3 dollars per mixed gallon.

Colloidal silica grout was developed to reduce the issue of syneresis with sodium silicates, to provide better control of gel times and achieve a lower viscosity. Colloidal silica grout is prepared in a multiple step process where a silicate solution is partially neutralized, leading to the formation of silica nuclei. Colloidal silica has the same expected life span as sodium silicate, but because of the multiple step process for development, prices are considerably higher, ranging from 13 to 15 dollars per mixed gallon.

Acrylics are defined as “true solution grouts,” which are free of suspended solids and have extremely low viscosity – similar to water. The acrylic family consists of acrylamide and acrylates. Each type requires a base resin to be mixed with a catalyst in order to create a gel matrix within a soil or rock with a controllable gel time. Acrylamide changes from a liquid to a solid in a controllable gel time ranging from 3 seconds up to 10 hours. Acrylate gel times range from approximately a minute to one hour. The life span of an acrylamide is estimated to be greater than 300 years while an acrylate is estimated to be approximately 50 years. The cost of acrylamide gel will typically range between 6 and 8 dollars per mixed gallon while acrylates are slightly more expensive, ranging between 8 and 10 dollars per gallon.

There are two primary types of polyurethane grouts defined as hydrophilic and hydrophobic. Hydrophilic grouts are typically single component systems that react with water and cure to an expansive flexible foam or non-expansive gel requiring a moist environment after curing. Hydrophobic expansive foams require little water to react, approximately 4%, and easily withstand wet/dry cycles. True hydrophobic foams, not requiring water to react, also are available. Hydrophilic foams expand 4 to 6 times their original volume, while hydrophobic foams expand up to 20 times original volume and may cure flexibly or rigidly. Most manufactures carry polyurethane resins having NSF or UL certifications approving use in potable water applications. The life span of polyurethane foam is estimated to be approximately 75 years. The cost of polyurethane resins (before expansion) will typically range between 60 and 80 dollars per gallon, uncured. It should be noted that the cost of polyurethane foams reduce drastically when one factors the expansive component of the material into the overall costs.